Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Parts & Accessories

Wheels Manufacturing Inc. Freewheel/BB Spacer
$2.49
Machined aluminum spacers for freehubs. Great for fine tuning freewheel and cassette placement or improving chainline. Also good for bottom bracket spacing with BSA BB cups. - Inner Diameter: 35.0mm - Outer Diameter: 40.7mm - Material: Aluminum - Finish: Polished - Bags of 10
Wahoo KICKR SNAP 142 x 12mm Thru Axle Adapter
$107.99
Our thru-axle kit comes with everything you need to mount most 12x142 thru-axle bikes on your KICKR SNAP indoor trainer. This accessory will work with all editions of the Wahoo KICKR SNAP. It includes the following: - Threaded axle spacer M12 x 1.75 Coarse - M12 x 1.5 Medium - M12 x 1.0 Fine - End Cap
Stan's NoTubes 3.30 Shimano/SRAM Freehub Body (9/10-speed)
$159.99
Replacement Shimano/SRAM freehub body for Stan's NoTubes 3.30 rear hubs.
Stan's NoTubes Neo Durasync Freehub
$119.99
Durasync freehub bodies feature triple freehub bearings for increased axle stability to handle even greater vertical and torsional loads. This CNC machined durasync freehub is a direct replacement for your Neo hub, and includes pawls, springs, pawl retaining ring, and red freehub spacer. Bearings are pre-installed. - 6-pawl system provides 36 points of contact and 10-degree engagement for quick acceleration - Chromed steel bearings - Wide bearing stance and axle design reduces flex and adds durability - Low drag main seal prevents contamination and reduces resistance - Mini Driver has a Shimano HG spline, but is 10mm shorter to accept 11-speed cassettes with 10t cogs from Hope and OneUp Components
Stan's NoTubes Rim Tape
$20.99 - $39.99
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3
Stan's NoTubes Tubeless Valve Stems
$24.99
Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.
SRAM 9/10 Speed Freehub Body for 746 Rear Hub
$94.99
- Original equipment freehub bodies to fit SRAM hubs and wheels. - Includes Right Axle End Cap
SRAM XD Driver Freehub Body for 746 Rear Hub
$114.99
- Original equipment freehub bodies to fit SRAM hubs and wheels. - Includes Drive Side Axle End Cap
Robert Axle Project Kid Trailer Thru Axle
$114.99 - $119.99
Purchase our Kid Trailer axle for your bike, and share your stoke for cycling with your kids. Simplify your life by allowing quick and secure attachment of your trailer to your best and favorite bike. Enjoy the adventure. Robert Axles for Kid Trailers are designed specifically to fit your 12mm thru-axle bike and allow attachment of any hitch-mounted trailer. These fit any trailer that has two wheels and a single point of attachment to the axle. This includes all the two-wheeled child, pet, and cargo trailers such as Thule, Chariot, Burley, Instep, Carry Freedom, and many more. - The axle shaft and axle end are precision CNC-machined. - The axle shaft is 7075 aluminum and hard black-anodized for rugged durability. - The stainless steel axle end allows for mounting of the hitch provided with your trailer. - Hardware for attachment of the hitch is included; the hitch, itself, is not. - No special tools required. Design allows for wheel installation and removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.
Robert Axle Project Trainer Thru Axle
$104.99 - $106.99
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
Race Face Turbine/Aeffect Replacement Freehub Body
$124.99
Replacement freehub body for Race Face Turbine and Aeffect wheels.
Race Face Vault Freehub Body
$124.99
Replacement freehub bodies for Vault hubs. - Use to replace worn/damaged freehub body or to switch cassette standards. - 60T
Muc-Off Rim Tape
$22.99 - $28.99
The Muc-Off Tubeless Rim tape is made from their proprietary performance material with a pressure-sensitive adhesive to provide just the right amount stretch whilst maintaining durability and strength needed to create a lasting airtight seal. Semi-transparent material makes locating the valve hole easy.
Mavic 135 > 142mm Rear Axle Adapters - Crossride
$15.99
On today's MTB frames, there are many dropout diameter and width standards. Most Mavic wheels can be fitted with specific adapters to match your wheelset with your frame. - Converts Mavic Crossride rear hubs with 135mm spacing to fit frames with dropouts spacing of 142mm - One pair of adapters required for each hub to be converted
Mavic 20mm Front Axle Adapter - Crossmax ST/SX
$14.95
On today's MTB forks, there are multiple front axle standards. Mavic front axle adapters allow you to mix and match without replacing wheels/forks. Most Mavic wheels can be fitted with specific adapters to match your fork end dimensions. - Converts Mavic Crossmax ST/SX front hub to use 20mm axle - One pair of adapters required for each hub to be converted
Mavic ID360 Freehub Body
$129.99
Get rolling again with a replacement freehub body for your Mavic wheels. - For Mavic ID360 hubs
Mavic XD Freehub Body
$134.99
Mavic's XD freehub body is compatible with all Crossmax and Deemax wheels (2012 and after) or all wheels using TS-2 hubs. This freehub body converts a rear wheel to work with SRAM's XD standard, making the wheel compatible with the XX1 drivetrain. Two kits are available : XD freehub body ITS-4 and XD freehub body TS-2, each with hub-specific parts.
Enduro ABEC3
$14.99 - $17.99
Grade 10 chromium steel balls
Enduro Max
$7.99 - $17.99
- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity
Easton 10-Speed Shimano/SRAM Freehub Body for M1SL hubs
$139.99
Replacement freehub bodies for Easton M1SL hubs. - Material: Aluminum - Cassette Body Type: Shimano/SRAM 8, 9, 10 Speed , Shimano Dynasys 11 Speed Mountain
DT Swiss Spoke Head Washer
$0.10
- Designed to stabilize 15g spokes in most hub flanges - 1000-pack
49°N Clamper Release Skewers
$14.99
A simplified quick release, utilizing an exposed/external split cam that straddles the end of the skewer. - Lighter and both easier and less expensive to manufacture, these external cam quick release levers represent an excellent value - Fits both road and mountain bike frames & forks with 100/130/135mm hub spacing - Construction: Chromoly steel skewer with alloy cam/lever and plastic/steel acorn-nut - Sold as a front & rear matching pair - Lengths: 133mm (FR) / 169mm (RR) - Weight: 58g (FR) / 64g (RR)
Page 1 of 1